JIEYO Stackable Energy Storage Battery — 48 V / 51.2 V LiFePO₄, 5 kWh–25 kWh, CAN/RS485, 6000+ Cycles

Сайтът JIEYO Stackable Energy Storage Battery is a modular, high-safety LiFePO₄ storage system engineered for residential and light-commercial solar applications. Each 51.2 V module provides approximately 5.12 kWh of usable energy, and modules stack vertically to scale from 5 kWh up to 25 kWh (and beyond in multi-stack arrays). With LFP chemistry, 6000+ cycle life, и CAN/RS485/RS232 communications to mainstream hybrid inverters, it is the practical core of an off-grid, hybrid, or on-grid backup system.

High-Performance LFP Platform (48 V / 51.2 V)

• Химия: Литиево-железен фосфат (LiFePO₄ / LFP) за стабилно термично поведение и дълъг експлоатационен живот.

• Nominal module voltage: 51.2 V (16S LFP).

• Energy per module: ≈ 5.12 kWh; stack 1–5 modules for ≈ 5–25 kWh.

• Живот на цикъла: Над 6000 цикъла (typical residential depth-of-discharge), supporting 10+ years of daily use.

• Ефективност при пътуване в двете посоки: high (> 95% typical), reducing system losses and improving PV self-consumption.

• Нисък саморазряд: holds charge well during seasonal or emergency standby.

Защо LFP за домашно съхранение? В сравнение с NMC и оловно-киселинните, LFP предлага превъзходен живот на цикъла, по-добра термична стабилност, и flatter voltage curves, which translate into predictable performance and lower lifetime cost per kWh.

True Stackable, Tool-Lite Installation

• Vertical stack design: modules align and lock mechanically; an upper control/BMS pack manages the whole stack.

• Floor-standing or cabinet/rack options: fits utility rooms, garages, equipment closets, or inverter walls.

• Quick electrical interconnects: short, labeled DC busbars/cables minimize wiring time and error.

• Expandable later: start at 5 kWh and expand to 10/15/20/25 kWh as loads grow—no redesign required.

• Clean footprint: narrow depth for tight spaces; front service access simplifies maintenance.

Интелигентни BMS и системни комуникации

• Наблюдение на опаковката: real-time voltage, current, temperature, and state-of-charge with cell balancing.

• Защити: over/under-voltage, over-current, short-circuit, over/under-temperature, and charge/discharge cutoff.

• Интерфейси: CAN / RS485 / RS232 for closed-loop communication to hybrid inverters and energy gateways.

• Event logging: aids diagnostics and after-sales service; supports firmware updates (where applicable).

• Compatibility: suitable for off-grid, hybrid-grid, and on-grid topologies; inverter brand maps available on request.

Режими на свързване към мрежата

• Извън мрежата: pair with a compatible hybrid/off-grid inverter for autonomous power where no utility is present.

• Хибридна мрежа: self-consumption, peak-shaving, and time-of-use arbitrage; charge from PV by day, discharge at peak.

• Резервно захранване от мрежата: maintain essential circuits during outages using an ATS/backup output from the inverter (per local code).

Машиностроене и опазване на околната среда

• Клас на защита: options up to IP54–IP65 (model-dependent), resisting dust and incidental moisture.

• Cooling: с въздушно охлаждане thermal path designed for quiet operation and long life.

• Enclosure: steel or alloy shell with powder-coat finish; corner reinforcement for logistics and on-site handling.

• Пригодност за експлоатация: modular architecture allows replacement at module level to minimize downtime.

Безопасност при проектиране

• Cell-level LFP safety with ceramic separators and prismatic/EV-grade cells.

• Pack fusing & contactors with pre-charge circuits to protect busbars and inverter DC link.

• Изолиране и изолация tested to relevant standards; creep distances respected for high-voltage stacks.

• Compliance documentation: CE / RoHS / MSDS / UN38.3 налични за логистика и навлизане на пазара.

Типични електрически характеристики*

(*Values vary by configuration; ask for the exact datasheet for your market.)

• Nominal voltage: 51.2 V per module; multi-module stacks managed by BMS.

• Usable energy: ≈ 5.12 kWh per module; 10–25 kWh in 2–5 module stacks.

• Recommended C-rate: 0.5 C continuous; 1 C peak capability depending on inverter and ambient conditions.

• DoD window: 90–100% configurable; standard warranty tied to recommended DoD.

• Ефективност при пътуване в двете посоки: > 95% typical with modern hybrids.

• Temperature: charge 0–45 °C, discharge −10–55 °C (typ.); store at 15–30 °C for best life.

• Комуникации: CAN / RS485 / RS232 with vendor-specific protocols selectable via DIP/firmware.

Use Cases

• Residential PV self-consumption: store daytime solar to cover evening peaks; raise PV utilization.

• Backup power: keep routers, lighting, computers, security systems, fridges and circulation pumps running during outages.

• Peak-shaving & TOU: charge off-peak, discharge on-peak to reduce bills.

• Small C&I micro-grids: stabilize loads in retail, workshops, telecom shelters, and remote cabins.

• RV/Marine cabins & lodges: stationary stacks can support longer stays with quiet, fuel-free energy.

Примери за оразмеряване на системата (илюстративни)

• 5 kWh (1× module): small apartments, routers/IT + lighting + intermittent appliance backup.

• 10 kWh (2×): typical 3–5 kW hybrid inverter for evening consumption and brief outages.

• 15 kWh (3×): longer autonomy for fridges, work-from-home setups, and pumps.

• 20–25 kWh (4–5×): extended backup for larger homes; pairs well with 8–12 kW PV arrays and 8–10 kW hybrids.

For runtime planning, a quick estimate is:
Runtime (h) ≈ Capacity (Wh) × DoD × system efficiency / average load (W).
At 25 kWh with 90% DoD and 92% system efficiency, you have ≈ 20.7 kWh usable—enough for ~20 hours at 1 kW average.

Бележки за инсталиране и пускане в експлоатация

1. Inverter pairing: choose an inverter with a supported CAN/RS485 profile; set battery type to LFP and select the JIEYO (or compatible) profile.

2. DC wiring: observe polarity and torque specs; use appropriately rated DC isolators and fuses per code.

3. Заземяване: bond enclosure and rack per local electrical code.

4. Ventilation: allow front/side clearance for airflow; avoid sealed cabinets in high-ambient rooms.

5. Firmware & BMS addressing: when stacking, set DIP addresses in ascending order; verify on the inverter screen/app.

6. Commissioning: charge to 100% on first run to sync SOC and perform BMS balancing.

Поддръжка и съхранение

• Periodic checks: confirm torque on busbars, inspect vent paths, and review BMS logs.

• Дългосрочно съхранение: keep at 40–60% SOC; top up every 2–3 months.

• Фърмуер: apply updates via approved channels when new inverter profiles or optimizations are released.

• Owner practice: avoid extreme heat or sustained high-C discharges to maximize life.

What’s in the Stack (Typical)

• 51.2 V LFP battery modules (quantity per order)

• Upper BMS/control module with display/indicators

• Base plate / stacking frame, inter-module busbars & fasteners

• CAN/RS485 communication cable to inverter, DC power cables (model-dependent)

• Ръководство за потребителя и ръководство за бързо стартиране; installation kit
  (Съдържанието се различава в зависимост от региона и избраните аксесоари.)

Сертификати и качество

• Safety and transport: MSDS & UN38.3

• Съответствие с пазара: CE / RoHS (others available on request)

• Фабрично осигуряване на качеството: incoming cell screening, cell matching, module aging tests, and full functional tests with BMS logging

OEM / ODM услуги

• Брандиране и етикетиране: logo, color accents, nameplates, packaging

• Electrical options: cable lengths, PV/communication connectors, fuse ratings, shut-down interface

• Mechanical variants: rack-mount kits, wall-mount brackets, dust-filters for harsher sites

• Картографиране на протоколи: CAN/RS485 profiles for specific inverter brands; integration guides for installers

Основни характеристики (моментна снимка)

• Battery type: LiFePO₄ (LFP)

• Model family: JY-S5000 / HV stack (regional naming may vary)

• Place of origin: Гуандун, Китай

• Grid connection: Off-grid, Hybrid grid, On-grid (via compatible inverter)

• Клас на защита: up to IP54–IP65 (by configuration)

• Cooling: Air cooling

• Живот на цикъла: 6000 цикъла (тип.)

• Communication ports: RS485 / CAN / RS232

• OEM/ODM: Acceptable

• Usage: Industrial / Commercial / Residential energy storage

Weights and dimensions depend on module count; sample single-module weights are typically in the 40–50 kg range, with total stack mass increasing linearly.

За кого е предназначен

• Homeowners wanting quiet, safe solar storage with room to grow

• Installers standardizing on a 51.2 V stack platform that scales from single homes to small businesses

• Project buyers needing documented, certifiable LFP storage with CAN/RS485 integration

• Energy-resilience users seeking peak-shaving, backup, and self-consumption in one system